[Table des matières] - [précédent] - [suivant]

Liste des protocoles supportés

Voici la courte liste des protocoles supportés à l'heure actuelle par Scapy :

ARP : ARP
ASN1_Packet : None
BOOTP : BOOTP
CookedLinux? : cooked linux
DHCP : DHCP options
DNS : DNS
DNSQR : DNS Question Record
DNSRR : DNS Resource Record
Dot11 : 802.11
Dot11ATIM : 802.11 ATIM
Dot11AssoReq : 802.11 Association Request
Dot11AssoResp : 802.11 Association Response
Dot11Auth : 802.11 Authentication
Dot11Beacon : 802.11 Beacon
Dot11Deauth : 802.11 Deauthentication
Dot11Disas : 802.11 Disassociation
Dot11Elt : 802.11 Information Element
Dot11ProbeReq : 802.11 Probe Request
Dot11ProbeResp : 802.11 Probe Response
Dot11ReassoReq : 802.11 Reassociation Request
Dot11ReassoResp : 802.11 Reassociation Response
Dot11WEP : 802.11 WEP packet
Dot1Q : 802.1Q
Dot3 : 802.3
EAP : EAP
EAPOL : EAPOL
Ether : Ethernet
GPRS : GPRSdummy
GRE : GRE
HCI_ACL_Hdr : HCI ACL header
HCI_Hdr : HCI header
HSRP : HSRP
ICMP : ICMP
ICMPerror : ICMP in ICMP
IP : IP
IPerror : IP in ICMP
IPv6 : IPv6 not implemented here.
ISAKMP : ISAKMP
ISAKMP_class : None
ISAKMP_payload : ISAKMP payload
ISAKMP_payload_Hash : ISAKMP Hash
ISAKMP_payload_ID : ISAKMP Identification
ISAKMP_payload_KE : ISAKMP Key Exchange
ISAKMP_payload_Nonce : ISAKMP Nonce
ISAKMP_payload_Proposal : IKE proposal
ISAKMP_payload_SA : ISAKMP SA
ISAKMP_payload_Transform : IKE Transform
ISAKMP_payload_VendorID : ISAKMP Vendor ID
IrLAPCommand : IrDA Link Access Protocol Command
IrLAPHead : IrDA Link Access Protocol Header
IrLMP : IrDA Link Management Protocol
L2CAP_CmdHdr : L2CAP command header
L2CAP_CmdRej : L2CAP Command Rej
L2CAP_ConfReq : L2CAP Conf Req
L2CAP_ConfResp : L2CAP Conf Resp
L2CAP_ConnReq : L2CAP Conn Req
L2CAP_ConnResp : L2CAP Conn Resp
L2CAP_DisconnReq : L2CAP Disconn Req
L2CAP_DisconnResp : L2CAP Disconn Resp
L2CAP_Hdr : L2CAP header
L2CAP_InfoReq : L2CAP Info Req
L2CAP_InfoResp : L2CAP Info Resp
LLC : LLC
MGCP : MGCP
MobileIP : Mobile IP (RFC3344)
MobileIPRRP : Mobile IP Registration Reply (RFC3344)
MobileIPRRQ : Mobile IP Registration Request (RFC3344)
MobileIPTunnelData : Mobile IP Tunnel Data Message (RFC3519)
NBNSNodeStatusResponse : NBNS Node Status Response
NBNSNodeStatusResponseEnd : NBNS Node Status Response
NBNSNodeStatusResponseService : NBNS Node Status Response Service
NBNSQueryRequest : NBNS query request
NBNSQueryResponse : NBNS query response
NBNSQueryResponseNegative : NBNS query response (negative)
NBNSRequest : NBNS request
NBNSWackResponse : NBNS Wait for Acknowledgement Response
NBTDatagram : NBT Datagram Packet
NBTSession : NBT Session Packet
NTP : NTP
NetBIOS_DS : NetBIOS datagram service
NetflowHeader? : Netflow Header
NetflowHeaderV1 : Netflow Header V1
NetflowRecordV1 : Netflow Record
NoPayload? : None
PPP : PPP Link Layer
PPPoE : PPP over Ethernet
PPPoED : PPP over Ethernet Discovery
Packet : None
Padding : Padding
PrismHeader? : Prism header
RIP : RIP header
RIPEntry : RIP entry
Radius : Radius
Raw : Raw
SMBMailSlot : SMB Mail Slot Protocol
SMBNegociate_Protocol_Request_Header : SMBNegociate Protocol Request Header
SMBNegociate_Protocol_Request_Tail : SMB Negociate Protocol Request Tail
SMBNegociate_Protocol_Response_Advanced_Security : SMBNegociate Protocol Response Advanced Security
SMBNegociate_Protocol_Response_No_Security : SMBNegociate Protocol Response No Security
SMBNegociate_Protocol_Response_No_Security_No_Key : None
SMBNetlogon_Protocol_Response_Header : SMBNetlogon Protocol Response Header
SMBNetlogon_Protocol_Response_Tail_LM20 : SMB Netlogon Protocol Response Tail LM20
SMBNetlogon_Protocol_Response_Tail_SAM : SMB Netlogon Protocol Response Tail SAM
SMBSession_Setup_AndX_Request : Session Setup AndX Request
SMBSession_Setup_AndX_Response : Session Setup AndX Response
SNAP : SNAP
SNMP : None
SNMPbulk : None
SNMPget : None
SNMPinform : None
SNMPnext : None
SNMPresponse : None
SNMPset : None
SNMPtrapv1 : None
SNMPtrapv2 : None
SNMPvarbind : None
STP : Spanning Tree Protocol
SebekHead? : Sebek header
SebekV1 : Sebek v1
SebekV2 : Sebek v3
SebekV2Sock : Sebek v2 socket
SebekV3 : Sebek v3
SebekV3Sock : Sebek v2 socket
Skinny : Skinny
TCP : TCP
TCPerror : TCP in ICMP
UDP : UDP
UDPerror : UDP in ICMP
_IPv6OptionHeader : IPv6 not implemented here.

Si vous souhaitez connaître la liste des protocoles embarqués dans votre version, utilisez la fonction ls() :

>>> ls()

Pour connaître les variables acceptées par chacun des protocoles, vous pouvez invoquer ce dernier dans la fonction ls(), ce qui nous donne, par exemple, pour le protocole IP :

>>> ls(IP)
version    : BitField             = (4)
ihl        : BitField             = (None)
tos        : XByteField           = (0)
len        : ShortField           = (None)
id         : ShortField           = (1)
flags      : FlagsField           = (0)
frag       : BitField             = (0)
ttl        : ByteField            = (64)
proto      : ByteEnumField        = (0)
chksum     : XShortField          = (None)
src        : Emph                 = (None)
dst        : Emph                 = ('127.0.0.1')
options    : IPoptionsField       = ('')

Tous les protocoles ne sont pas encore documentés (!) au sein du moteur. Ainsi, si vous essayez de lister un de ceux-ci, vous reviendrez simplement au prompt :

>>> ls(SNMP)
>>>